2009 MAZDA 6 SERVICE MANUAL PDF

Quick Links. Table of Contents. General Information. Fuel and Emission Control. Heater and Air Conditioner Systems. There are explanation given only for the sections.

Author:Vijin Zulujind
Country:Monaco
Language:English (Spanish)
Genre:Science
Published (Last):15 September 2006
Pages:455
PDF File Size:7.14 Mb
ePub File Size:8.41 Mb
ISBN:993-5-62347-294-5
Downloads:91108
Price:Free* [*Free Regsitration Required]
Uploader:Faemuro



Quick Links. Table of Contents. General Information. Fuel and Emission Control. Heater and Air Conditioner Systems. There are explanation given only for the sections. Automobile Mazda 6 Smart Start Manual 26 pages. This manual Propeller Shaft should be kept up-to-date. Page 3 The contents of this manual, including drawings and specifications, are the latest available at the time of printing, and Mazda Motor Corporation reserves the right to change the vehicle designs and alter the contents of this manual without notice and without incurring obligation.

GI-7 GI— Therefore it may not contain the necessary reference service procedures to perform the service indicated in this manual.

End Of Sie GI— Serial No. Page 8 3 : In some models, there is a fuel pump relay that controls pump speed. That relay is now called the fuel pump relay speed. All inspections and adjustments must be made by an expert repairer, we recommend an Authorized Mazda Repairer. Brake fluid Replace brake fluid. Page 13 DTC P F DTC P Page 14 DTC P F NO. If the voltage from accelerator pedal position sensor No.

The PCM calculates the deviation of the interval time for each cylinder. If the deviation of interval time exceeds the preprogrammed criteria, the PCM detects a misfire in the corresponding cylinder. If the glow relay voltage is 4. Always carry out a total inspection of the input systems, output systems, and PCM to determine the cause of trouble.

Page 46 Idle: Approx. Verify that the voltage at terminal B changes while applying the vacuum to the EGR valve as show in the graph. Specification 0. Perform the necessary vehicle preparation and visual inspection. DTC troubleshooting completed. If the fuel pressure is lower after the fuel injection than the preprogrammed criteria, the PCM determines fuel system leakage.

If the difference between the maximum and minimum value of the intake air temperature sensor No. If the voltage characteristic of the air flow sensor signal is out of the threshold, the PCM determines that there is a malfunction in the mass air flow sensor. If the difference of the vacuum inside the intake manifold during middle engine speed and low engine speed is less than the threshold, the PCM determines that there is a malfunction in the manifold absolute pressure sensor characteristic.

If the voltage from the manifold absolute pressure sensor is more than 4. If the voltage from the engine coolant temperature sensor is less than 0. If the voltage from the fuel temperature sensor is less than 0. If the voltage from the fuel temperature sensor is more than 4. Troubleshooting completed. If the PCM does not receive the injection confirmation signal for unspecified cylinder normally, the PCM determines that the unspecified cylinder fuel injector operation is not verified.

Go to the next step. If the idle switch is off even if the voltage from the accelerator pedal position sensor is less than 0. Page Yes Inspect suspected circuit or part or both according to the inspection results. If the EGR solenoid valve vacuum voltage is low even if the EGR solenoid valve vacuum is off, the PCM determines that there is a malfunction in the intake shutter solenoid valve control circuit.

Page Dtc P — Less Than 0. If the PCM detects the circuit current is less than 1 A when the suction control valve is on, the PCM determines that there is a malfunction in the suction control valve circuit. If the PCM detects circuit current is more than 1 A when the suction control valve is off, the PCM determines that there is the malfunction in the suction control valve circuit.

If the intake shutter solenoid valve half voltage is less than 7. If the intake shutter solenoid valve half voltage is more than 7. If the intake shutter solenoid valve full voltage is less than 7.

If the intake shutter solenoid valve full voltage is more than 7. If the PCM detects that the input voltage for any cylinder is more than 4. If the voltage of the variable swirl control solenoid valve is high even if the variable swirl control solenoid valve is on, the PCM determines that there is a malfunction in the variable swirl control solenoid valve control circuit.

If the voltage of the variable swirl control solenoid valve is low even if the variable swirl control solenoid valve is off, the PCM determines that there is a malfunction in the variable swirl control solenoid valve control system.

If the PCM does not receive the injection confirmation signal for No. If the difference between the barometric pressure input from the barometric pressure sensor and the manifold absolute pressure is more than 75 mmHg, the PCM determines that there is a malfunction in the barometric pressure sensor.

Page No. Go to Either or other condition appears: Step 10 for vehicles without immobilizer Go to the next step. Go to the appropriate DTC test. Retrieve any DTC.

Communication error message is displayed: Is the DTC displayed? End Of Sie NO. Go Either or other condition appears: to Step 10 for the vehicles without Go to the next step. Go to appropriate DTC test. Inspect for the following: Go to the next step.

Is the engine overheating? Adjust the accelerator position sensor and the idle Are the accelerator position sensor and the idle switch correctly. Inspect the neutral switch adjustment. Replace the turbocharger. Does the wheel turn easily and smoothly?

Inspect if the turbocharger turbine wheel is Replace the turbocharger. Is the fuel injector normal? Repair or replace if necessary. Inspect the IDM. Is the IDM normal? Is there any problem? Is any engine oil found inside the turbocharger Excessive amount of oil is found Does the engine run cold?

Perform the self-test function using the WDS or Page 2. Make sure that all the hoses are securely connected in the proper position. Turn the engine switch to the ON position. Verify that the PID value is within specification. Specification: 0. Start the engine and run it at idle speed. ST-2 ST— Print page 1 Print document pages. Cancel Delete. Sign In OR. Don't have an account?

Sign up! Restore password. Upload from disk. Upload from URL.

IT HAPPENED IN INDIA KISHORE BIYANI PDF

Mazda 6 Service Manual

We have 23 Mazda 6 manuals covering a total of 33 years of production. This like all of our manuals is available to download for free in PDF format. How to download a Mazda 6 Repair Manual for any year. In total, that's over pages of content dedicated to your Mazda 6. We get a lot of people coming to the site looking to get themselves a free Mazda 6 Haynes manual. We'll send you a quick email a new Mazda 6 document is added. Spam free: Maximum of 1 email per month.

JAVA MATTONE DOPO MATTONE PDF

Mazda 6 Workshop & Owner’s Manual PDF

Mazda 6 Workshop Manual with L8 1. Including restyled models since Catalog of spare parts. Typical faults. Guide to repair and maintenance. The Mazda 6 manual includes detailed instructions on how to use the self-diagnosis system, included automatic transmission, ABS anti-lock braking system , TCS anti-skid system , SRS airbag system and recommendations for adjusting mechanical and automatic transmissions, adjusting and repairing elements of the brake system including ABS and EBD electronic brake force distribution system , steering, suspension car Mazda 6.

ALCHOURRON BULYGIN PDF

Mazda 6 Workshop Manual

.

Related Articles